Braided Brake Lines: The Complete Guide
Braided brake lines are one of the most effective upgrades you can make to any car's brakes, and one of the cheapest. They don't add stopping power on their own, but they change how the brakes feel: a firmer, more consistent pedal that doesn't go soft as the brakes heat up. This guide covers what braided brake hoses are, how they compare with rubber, how to choose the right fittings, how to measure for a replacement, and when it's time to change them.
What is a braided brake line?
The flexible hoses that connect your car's rigid brake pipes to the calipers have to move with the suspension and steering. On most cars they're made from rubber. A braided brake hose does the same job, but it's built differently:
- PTFE inner core: the tube that carries the brake fluid. PTFE (Teflon) is chemically inert, unaffected by brake fluid, and stays dimensionally stable when it gets hot.
- Stainless steel outer braid: a woven stainless jacket that stops the core expanding under pressure and protects it from abrasion and stone chips.
- Protective coating: our hoses have a PVC coating over the braid, which keeps dirt out and stops the braid chafing anything it touches.
Braided vs rubber brake hoses
When you press the brake pedal, the fluid pressure in the system can reach well over 1,000 PSI. A rubber hose swells slightly under that pressure, and some of the force from your foot goes into stretching the hose instead of clamping the pads. As rubber hoses age, they swell more. That's the soft, spongy, long pedal that older cars are known for.
A braided hose barely expands at all, so more of your effort reaches the pads. In practice that means:
- A firmer, more precise pedal with a more consistent biting point.
- Consistent feel when the brakes are hot, which matters on track days and fast road driving.
- Better durability: the stainless braid resists cuts, abrasion and perishing far better than rubber.
Braided hoses don't shorten your stopping distance by themselves. That depends on your pads, discs, tyres and calipers. What they do is give you a pedal you can trust and modulate accurately, which is what lets you use the grip you have.
Our hose specification
Every brake hose we build uses the same specification:
| Inner core | PTFE, 3mm (1/8") internal diameter |
| Outer braid | Stainless steel, PVC coated, 8mm (5/16") outside diameter |
| Max working pressure | 4,206 PSI (290 bar) |
| Burst pressure | 12,618 PSI (870 bar) |
| Operating temperature | −70°C to 250°C |
| Minimum bend radius | 19mm |
| Fittings | 303/304 stainless steel, made in Great Britain |
| Lengths | Built to order from 80mm to 8,000mm |
| Colours | Red, blue, black, yellow, orange, green, purple, carbon and clear |
Choosing the right end fittings
The hose itself is the easy part. Getting the right fitting on each end is where most people get stuck. Four things decide which fitting you need:
- Thread size and pitch. Common brake threads are M10x1, M10x1.25, M12x1, 3/8" UNF and 7/16"x20. M10x1 is by far the most common on European cars. Pitch matters as much as diameter: an M10x1 will start into an M10x1.25 port and then bind.
- Banjo, male or female. A banjo bolts straight onto the caliper with a banjo bolt and two copper washers. A male fitting screws into a port; a female fitting receives a male union on a rigid pipe.
- Fixed or swivel. A swivel fitting rotates on the hose so you can line it up without twisting the hose. It's easier to fit in almost every case.
- Circlip groove or plain. Many VAG, Ford, Renault and Toyota cars hold the hose in a chassis bracket with a horseshoe clip. If your original hose is held by a clip, you need a circlip groove fitting and a matching retaining clip.
Fittings also come in straight, 20°, 45° and 90° angles, so you can route the hose cleanly around a caliper or suspension arm without kinking it. For a full explanation of thread types, bulkhead fittings and adaptors, read our Brake Line Fittings and Adaptors guide.
How to measure for a replacement hose
- Measure the old hose from end to end, including the fittings, with the hose laid straight. If you're copying an original hose, that's your starting length.
- Check the movement. With the car on stands, check the hose at full steering lock in both directions and with the suspension at full droop and full compression. A hose that's too short will be stretched; one that's too long can rub on the tyre or suspension.
- Allow for the bend radius. Our hose shouldn't be bent tighter than 19mm. If the routing is tight, an angled fitting is usually the better answer.
- Note both ends. Write down the thread, fitting type and angle at each end before you order.
Not sure? Send us a photo of your old hose ends, or your vehicle make and model, at [email protected]. We build these every day and can usually identify the fittings from a picture.
Custom hoses vs vehicle-specific kits
For popular cars we already have the dimensions and fittings worked out, so you can order a ready-specced kit:
- Abarth 500, 595 & 695 brake hose kits
- Renault braided brake hose kits
- VW Transporter & Caddy brake hoses
- Ford braided brake hose kits
- Land Rover braided brake hose kits
- Mazda MX-5 brake & clutch hoses
For anything else, such as race cars, kit cars, restorations, motorcycles, clutch lines and one-off projects, use our Custom Braided Brake Hose Builder. You choose the fitting and angle at each end, the colour and the exact length, and see the hose update as you build it. Read more about how it works in Introducing the New Custom Braided Brake Hose Builder.
Braided brake lines for motorcycles
Bikes benefit from braided lines just as much as cars, often more, because the lever feel is so direct. Most motorcycle brake systems use banjo fittings at both the master cylinder and the caliper, which the builder covers in M10 and 3/8" sizes, with angled banjos to clear forks and handlebars. Measure the original line with the bars on full lock in both directions.
Fitting tips
- Always use new copper washers on banjo bolts. They crush to seal and shouldn't be reused.
- Don't twist the hose as you tighten the fittings. Hold the hose and turn only the nut.
- Secure the hose with the original brackets or hose locators so it can't rub on the tyre or suspension.
- Bleed the system thoroughly with fresh fluid afterwards. A high-boiling-point fluid such as Motul RBF 660 suits fast road and track use. If a bleed nipple is seized or rounded, we stock stainless bleed nipples.
- Check for leaks with the pedal held down firmly, and check the routing again at full lock and full droop.
Brakes are safety-critical. If you're not confident fitting brake hoses yourself, have the work done by a qualified mechanic.
When should you replace your brake hoses?
There's no fixed interval, but check your hoses whenever the car is serviced and replace them if you see:
- Cracks, perishing or splits in the outer surface
- Bulges or swelling, especially when the pedal is pressed
- Chafing, kinks or damage from rubbing on the tyre or suspension
- Fluid weeping at the fittings
- A pedal that has become soft or long even after bleeding
Brake hoses are also checked at the MOT, and damaged, chafed or bulging hoses are a common reason for a fail.
FAQ
Are braided brake lines worth it on a road car?
Yes. They're one of the best-value brake upgrades for any car, and on an older car they often transform a soft pedal. They also outlast rubber hoses.
Do I need to change the brake fluid when fitting braided hoses?
You'll need to bleed the system after fitting new hoses anyway, so it's the ideal time to replace the fluid completely.
What colour should I choose?
Colour is purely cosmetic: every colour uses the same hose and the same pressure rating. Pick whatever suits your car.
Can you make clutch hoses too?
Yes. The builder includes dedicated clutch fittings for Audi, BMW, Ford and Renault, and we make braided clutch hoses for a range of cars.
Build yours
Start with the Custom Braided Brake Hose Builder, or browse the full range of hoses, fittings and accessories in Braided Brake Hose & Brake Fittings. Every hose is built to order in our Aberdeenshire workshop. Free UK delivery on orders over £150.
